How to Install a Range Hood Vent Though the Ceiling

How to Install a Range Hood Vent Though the Ceiling

You may be aware of all the benefits of range hood roof vents.  However, do you know how to install one? Do you know that you can use the simplest of tools and the shortest of time to install one in your house? For many years now, I have been advocating for DIY services and I continue to do so whole-heatedly. Basing on my experience in the field, installing a range hood vent through the ceiling is one of the easiest of tasks. I am ready to share with you my tricks through this article. I can guarantee you that by the end of this article; you will have received all the basic information and tricks on how to go about this simple task.Need to know more about how to install a Range Hood vent though the ceiling

Every house needs a range hood vent especially in the kitchen because it allows hot air and cooking odors to vent out of the house efficiently. In addition, the range hood vent helps keep your kitchen surface clean because it prevents formation of grease.

What is more is that you can install a range hood vent through your ceiling all by yourself. Save yourself from the cost of having to pay a professional to do a job that you can manage just by putting in extra effort

Materials needed

For the whole process to be successful, you need the following materials:

  • check
    Duct flashing
  • check
    Vent cap
  • check
    Wire nuts
  • check
    Electrical cable
  • check
    Roofing tar
  • check
    Duct strap
  • check
    Metal ducting
  • check
    Range hood
  • check
    Cable clumps
  • check
    Screw anchors
  • check
    Vent cap

Tools Needed

  • check
    Glasses to provide safety
  • check
    Caulking gun
  • check
    Electric drill
  • check
    Reciprocating straw
  • check
    Gloves
  • check
    Tape measure
  • check
    Sheet metal shears
  • check
    Drywall saw
  • check
    Screw drivers
  • check
    Drill bits
  • check
    Hammer
  • check
    Wire cutter

The time that you will take to complete the whole process will depend on your skill level. For instance, if you are a beginner, you will need about six to eight hours. For an intermediate, you will need around five hours while and an advanced level will need four hours.
Before starting the installation process, make sure that the circuit that you will be working on is turned off and that all your tools are working properly. 

Pro tips

My experience dictates that you should buy slightly larger range hood vents because smaller ones tend to produce a lot of noise. Also it is better to have a large fan running slowly than to have a small fan running faster because the later produces more noise.
In addition to that, for a successful project, you need to plan well before starting the process. Make sure that you have all the necessary tools and materials that you will need for the process to be successful. 

Steps to follow

After gathering all the materials and tools for the job, here are the steps to take when looking to install vent a hood reviews through the ceiling successfully:

Removal of the fan

The first step is to remove the complimentary parts such as the filter, fan, electrical housing and the light housing from the range hood vent that you want to install. After that, ensure that the hole located on the top side of your hood is open.

Make an outline

The second step involves outlining of the part of the ceiling where you want to mount your range hood vent. You can achieve this by holding up the vent then using a market to outline its dimensions. In some cases, you might to need to make the same corresponding outline on the upper side of the cabinet.

Drilling of holes

Using the outline that you had created, drill holes in all of corners of the outline ready for the mounting process. A reciprocating saw should help you cut easily from one hole to another. For the outline that you made on top of the cabinet, you should repeat the hole drilling process until they are all perfect. You should then drill a hole on your ceiling board where the electric cable will pass through. Remember, the hole should be of the same size as the one on the knockout outline for easier pulling of the electric cable once the process is over.

Make a hole on the roof

Once you have made a path on the ceiling, the next step is to create one on the roof that will see the range hood vent reach outside. This a process that many people perceives to be hard but with little accuracy, you can achieve greatness by yourself. First, you need to choose a location on your roof that is not further from the path you have made on your ceiling and drill an equally sized hole. If possible, rely on the hole that you made first to create the second. Tools that are more diverse may be needed at this stage especially if you have a roof with a different design from the normal.

Join the parts of the hood

After creating the paths where the hood vent will pass through, the next step is to join all of its parts in place ready for the actual installation process. Remember to install the cable clamp and hold it in place (you might need a hand on this

Installing of the best vent hoods

After ducting the joints of the hood in place strongly, the next step is to install the hood in place. Pass the upper side of the hood through the holes that you made and fit it in place. At this stage, the most important thing is to ensure that you duct the hood properly to avoid possible leaking and prevent the parts from falling off. However, you should be careful not to obstruct the damper in the hood with the duct tape. The damper should move freely at all times for better effectiveness of the hood vent.

Sealing the upper parts of the best hood

After putting the best hood vent in place, you should then seal the ducting that goes through the ceiling. I personally find this stage challenging but with a bit of focus I always get it right in the end. I usually put the duct flashing in a position where it can easily pass through the flange. Use roofing tar to seal the parts effectively and complete the installing process. The joints located between the flashing and the duct should be sealed using roofing tar. Finally, you should place a vent cap over the duct of the hood vent to prevent unwanted objects from passing through it.

Complete the process

If there was a fan unit install before, place it back carefully by reconnecting the wires matching each of their colors. Use wire nuts to cover your connections and once you are sure about your re-connections, turn on the power. Clean the tools and return them to their respective places of storage.

Conclusion

It is my sincere hope that this article turned out handy for you. Remember that you can always do these DIY procedures (like installing a range hood through the ceiling) yourself thereby cutting on the expenses of hiring a professional. All you need to do is make sure that you have all the materials and tools that you will need before starting the process. Also, you should monitor and know the type of ceiling that makes your house. Different ceilings require different techniques so it is only by figuring out some basic facts about them that you will be able to install a range hood vent through it. In addition to that, in as much as this is a DIY process, you might require a helping hand especially when mounting the hood vent to the ceiling. 

If you liked this article, kindly leave a comment below and like it. All your feedback will be highly appreciated because together we make each other better. 

About the Author Frank J

follow me on:

Leave a Comment: